Tranny (shifter) bokerforked (Found: star cam broke off the shift drum!)

wfooshee · Jun 12, 2014

Went to shift down from 3rd to 2nd a while ago and something broke. Shifter wiggles but doesn't engage anything, and bike is between second and third, ALMOST in second. It's close enough to being in second that a little bit of clutch will start to move the bike and then it starts with the dog-slipping noise, which makes me bring the clutch lever back in quickly.

This truly sucks.

I was ONLY about three miles from home, so I pushed/rode it like that, just enough clutch for a tiny bit of thrust. Took 90 minutes to get home! For once, Florida flat is AWESOME!!!!!! because it wouldn't have climbed anything steeper than .03% grade.

So it's parked. I have no idea what I'm going to do. I don't have a lift, nothing to raise the bike/drop the motor, and no spare parts bin lying around full. I'm supposed to have dibs on second gear parts from Patriot's blowed-up motor, but I can't find the thread about that for some reason, and I don't remember who it was put all that stuff in his attic. I might see if some other parts are there for me....

Might be cheaper to buy an eBay engine if I find one than to buy parts, assuming I can't get what I need from Patriot's motor if I find that forum member again.

So someone remind me who that was, and I can start begging him to get up into the attic.

rPGoatBoy · Jun 12, 2014

Taking on a job like splitting the motor for transmission repair shouldn't be done with high mileage replacement parts, lest ye be wanting to take the job on a 2nd time. How many miles are on your bike now? I'd start by pulling the clutch basket out and making sure the other end of the shift shaft is contacting the tits on the shift drum correctly. Unlikely to be a problem there, but you just may get lucky and not have to yank the motor.

Take a look at StreetHawk's writeup and see if you'd be comfortable doing something like he did. Most of the work is getting the motor out, splitting it for transmission repair isn't too challenging; probably can be done for around $500-600 in parts depending on what's wrong and you can buy parts cheaply online. Also, motor out means it's a GREAT time to take on a valve shim adjustment, CCT replacement, suspension rebuild/upgrade, etc.

The downside is the wait. You're probably gonna be without an FJR for at least a couple of months.

dcarver · Jun 13, 2014

Ahh, FooShee ...

A reference point..

I bought a 2008, 5k engine, delivered from GA to CA for 1,200 USD.

It's been a perfect engine.. Better than OEM..

It took less time to replace the engine than a head gasket...

If me, I would replace and go.

Be sure the replacement engine does NOT have broken tabs, and ask to see a video of the running engine, with sound, prior to engine extraction..

Sorry to hear of the problems....

JamesK · Jun 13, 2014

Damn Wfooshee, sorry to hear about this. I too am curious about the mileage on this engine.

dcarver · Jun 13, 2014

I gots to meet this JamesK doode..

Back the thread now...

Mihalis fjr · Jun 13, 2014

Wfooshee,sorry to hear this..here is the threads from Patriot's engine:

https://www.fjrforum.com/forum//index.php/topic/151853-what-happened-to-isabellas-engine/

https://www.fjrforum.com/forum//index.php/topic/150618-running-bad-feeling-blessedlimped-home-walking-on-air/

Fred W · Jun 13, 2014

Sorry to hear it, Walt. That is not a very common failure mode of the shifting mechanism, so not much sage advice around on what it might be.

I believe it was hppants that hung onto Patriot's old engine. Redfish Hunter and he were the ones to fetch the bike with Patriot, as I recall. And I think they grabbed the engine then too.

I guess I'd look at how many miles you have on your old engine and consider a total engine swap. It's either that or do a tear down and see what is actually wrong and how much it would cost for parts but that will be the more labor intensive route.

Good luck, man.

RossKean · Jun 13, 2014

+1 on rPGoatBoy's comment on replacing hard-to-access parts with high mileage used parts. The labor is worth more than the cost saving and you DON'T want to do it twice. I think I would opt for a replacement engine, especially if yours has a lot of miles on it.

wfooshee · Jun 13, 2014

Mine just turned 90,000 a couple of weeks ago.

I'm not too worried about comparing parts from mine and Patriot's as far as age or mileage, as I remember a comment made during the teardown: Mike, you can ride my bike anytime.! OTOH, not sure the parts I will need are still available from that one.

08FJR4ME · Jun 13, 2014

With that kind of mileage I don't think I would bother. If its not an easy fix I would be looking at second hand or something new. That's a crapload of work and something I would not attempt on my own. Just my thoughts for what its worth.

Good luck,

Dave

lnewlf · Jun 13, 2014

Used mill might have tranny problems too-fork and dogz..no way to tell..I once changed out the engine on a Sazook RF900 to fix jumping out of gear problems and found that the replacement engine had the same problem...Even so, I would prolly switch the old mill for a newer low mileage one...fingers crossed.

Mihalis fjr · Jun 13, 2014

The location of the seller is the Florida..Good price i think...

https://www.ebay.com/itm/ENGINE-MOTOR-FJR1300-FJR-1300-ABS-YAMAHA-05-Y-/201036903426?pt=Motorcycles_Parts_Accessories&hash=item2ecebbb402&vxp=mtr#shpCntId

rushes · Jun 13, 2014

Easy fix...

Just tryin ta help.

escapefjrtist · Jun 13, 2014

rushes said:
Easy fix...

Just tryin ta help.

It's not a problem if it can be solved with $$$!

Good luck Walt.

--G

Aasland · Jun 13, 2014

I have idea.

I have a spare 2006 (GEN 2) with 97k on it. But it is missing 2nd gear. So scratch that idea.

I have another idea:

I have a 2007 Gen 2 engine with 25k on it that runs great. But I think you have a Gen 1 so scratch that idea.

I have another idea:

That 2007 engine is in a 2006 FJR. Everything works. I'll sell the 2006 bike, with the 2007 engine installed, for $5500. But you're in FL and I'm in MN. Scratch that idea.

I have another idea:

You fly up here and buy my 2006 with the 2007 engine. When you get home you can move your farkles to the newer bike, and part out the rest of it.

How does that sound? Lots cheaper than a 2014 ES.

Fred W · Jun 13, 2014

Many 1st gen farkles do not transfer to later gens. Scratch that idea...

wfooshee · Jun 13, 2014

Don't like that 2006 blue anyway!!!

clocklaw · Jun 13, 2014

Here is another e-bay bike from Florida, might be close enough for you to drive out and pick up? I have bought from these guys before and got what I expected.

https://www.ebay.com/itm/03-05-Yamaha-FJR1300-Motor-Engine-GUARANTEED-/380811463228?pt=Motorcycles_Parts_Accessories&hash=item58aa21ca3c&vxp=mtr

Or if you're real lazy, just by Bungie's 2004 and swap the tags over.

dcarver · Jun 13, 2014

Sometimes, it all just sucks!

Tranny (shifter) bokerforked (Found: star cam broke off the shift drum!)

Help Support Yamaha FJR Motorcycle Forum:

O, Woe is me!!

Well-known member

Well-known member

Got to ride

Well-known member

Well-known member

1 Wheel Drive

Well-known member

O, Woe is me!!

-WYNPRO-

Well-known member

Well-known member

Well-known member

Searching for Dry Roads

Depleted

1 Wheel Drive

O, Woe is me!!

Well-known member

Well-known member

Similar threads

Join the conversation!

Join today and get all the highlights of this community direct to your inbox. It's FREE!