Search results

Good info thanks for posting the pics and information.

https://ridermagazine.com/2019/01/24/motobikejack-gear-review/ I have one of these divided in three separate bags to even the 8 lbs weight. One in each side bag and last one in trunk for solo long trips. I'm tall and 73 with arthritis in my hands and lower back reason I ride a AE no clutch...

Thanks looks like a diaphragm clutch disc concave facing in. I bled my 2008 AE clutch every winter useing on/off on bars etc without removing all the rest parts to get to rear on clutch actuator.

Go into Diagnostic and read your FSM.on how to acess it checks side side switch on/off and checks injectors and resistors in spark plugs etc Chapter 8 has a list of error codes and what to check.

The rear still has the original OEM pads I clean the piston on it too like the front. I doubt I'll take it apart yet I'm easy on the rear and bleed both brakes and clutch every set of tires or two years.

My brake lines aren't cracked and still look good and not rock.hard. My 2008 had always been garaged. So no not replacing my hoses yet. Laughing replace every 4 years. At 59,000 miles last set of tires I replaced my brake pads and after inserting a a thin piece of wood to expose my pistons in...

Following next set of tires on my 2008 AE thought I would replace the piston seals.

I like the added turn signals on the back side of the bags. No doubt what direction you are turning in the dark. The light bars break up how wide the bag looks is hanging off the frame from the rear. The decal with large Yamaha tuning forks makes the bags look thinner thinner. I know you can't...

I've read all that too years ago. With my garage door closed I check my GIVI tail lights make sure stop lights work before opening the door and starting the engine. 3 years 15,000 miles so far no issues with the GIVI quick disconnect. I purchased two of them 3 years ago for a back up. So far...

I wouldn't let a dealer touch.my FJR1300 good thing it's a 2008 AE most Yamaha dealers will not repair a Yamaha that is older then 10 years. Most dealers have very little maintenance experience with a FJR especially my 2008 AE.. If your brake lines are not rotted, cracked etc I wouldn't change...

I use a GIVI E52 liter trunk with thr SR357 steel bar brace for the Money quick release mount. GIVI has a quick release light kit the goes in the top of the Monokey quick release mount that bolts to the SR357. The bottom of my GIVI trunk with their light kit has a twin tap round connector the...

What is the "Judder Spring" that was in backwards?????? I have a 2008 AE like Brodie and I have spare clutch and transmission actuators after reading Brodies thread for YCCS error code 37 .

Welcome from Ft Worth Texas.

Last year I noticed oil spots above the full line in my radiator resivor tank. The hose from the tank goes to the top outlet of the water pump. The mechanical oil seal behind the impeller was starting to fail. I purchased a Gen III pump vs parts to repair. The resivor had crack on the inside I...

I would replace the pump with a Gen III vs purchasing parts to repair it. I went thru this on my 2008 and realized Yamaha only sold replacement parts for Gen I/II. Then looked at new Gen III for parts and realized Yamaha sold a complete pump assembly. I found a 2018 pump Ebay 21,000 miles $50 I...

Have you used a 50/50 mix to clean injectors and carbon off valves with Seafoam ? I use it for winter storage no ethanol issues after a long winter. I've never used Yamaha fing free.

https://www.mooremafia.com/

I installed the Helibar Riser Plate kit that bolts on the the top triple tree clamp for up 1' and back almost 4". I wanted more height so I stacked my Genmar 1" riser blocks on top of the Helibar Plate kit on my 2008 AE. I purchased longer stainless steel bolts too mount the handle bars on the...

Well done I like the detail and the explanations, like line up triangle marks etc and the white dots. Pointing the out the clutch springe (diaphragm plate) is not flat. Good quality pictures, thanks for time and effort. Louis

You can Google Yamaha recall site select motorcycle enter your vin# to see if your model had or needed the ignition switch recall and # 4 ground connector with distribution clip (spider) had the second ground wire added as I posted for you to solder a wire on #6 while you have the fairing. Doing...