Search results

I waited too long sigh...I contacted Gaurald last year about painting the top of my GIVI E52 trunk metallic silver match side covers and tail, $125.00 plus shipping both ways.

My 2008 AE is smooth off idle slow speed maneuvers no problem. Yamaha did remap in 2008. We raised the values up some like the BJM no difference. We took several turns out of the top throttle body spring, this made the throttle MUCH easier to turn and helped off idle maneuvers making slight...

Does it matter what year Gen III? I read a discussion about LED in FJR, the Gen II was not made for a LED a cross eyed pattern is the result. And the Gen III was made for LED. IIRC it was the later Gen III that came with LED so I wondered about that. I installed H4 F2 9003 LED with fans in my...

I have notice several members posted the 2008 has the lean off idle stumble like the 2006/2007. I have a 2008 AE 58,000 miles and it's smooth off idle no Ivan flash. When we installed a used "Brodie" bypass ground harness I noticed larger Black ground wire to #4 connector that has the "spider"...

Howdy from Ft Worth Google Yamaha recall site, enter the 2008 vin# to see if its had the ignition switch and #4 ground wire done. #4 ground connector had the first " spider" distribution clip inside.

I looked for the PM and only found "Start A conversation" or I would have PM you back. So..... please explain how to access the PM function. Regards Louis

Funds sent PayPal Thanks

76148. Ft. Worth, TX Please email pic of it and harness. T.I.A. Louis

Search FJR1300 owners forum IIRC someone posted Brodie or Roadrunner parts list for matching connectors part# and length of wire to build one. Do a search here too, Brodie posts here sometimes maybe he will see this and posts where he purchased the connectors etc. I lucked out 2 two years...

Check your vin# on Yamaha recall site for ignition switch and #4 ground wire recall. Purchase a 2008 AR Yamaha FSM and read up on bleeding the AE clutch and ABS. You have jump.pins in harness to activate ABS pump the bleed ABS distribution block. I have 57,000 fun miles on my granite metallic...

Brodie Appreciate the info and for SURE I will use my front wheel chock, copy holding the bike upright. I drive up my ramp on my Direct Lift Pro Cycle DT with a pair optional 24" side rails and ramp extension into the chock and get off. After the rear is in the air a foot or two with the pipe...

Brodie Thanks for the advise, I have a chock bolted on my Direct Lift. What diameter pipe and lengths did you use? I purchased one of Russell Holden pivot arm with grease zerks. While I have it all apart I will inspect the connectors you repaired. My 2008 AE has 57,000 miles and shifts like...

A Gen III complete pump will fit any year FJR. I purchased a low milage used 2018 water pump and used my 2008 front cover so it matches. I ordered a new O ring and outer front cover gasket/ O ring Easy to remove, twist and pull. I was surprised to learn Gen I and II Yamaha sold parts to rebuild...

Old thread but I thought this might help others too. I read a thread that after everything was to FSM and his hand were numb the owner adjusted the internal "Balance Shafts" . Problem solved. IIRC it was a gen I.

Old thread and glad the link was posted on F.B. I too have a 2008 AE 57,000 miles. I am printing these pages and hope mine does not throw that code. I am going to install a pivot arm for the shock linkage that has the ( Russell Holden) grease "zerk" mod. This would be a good time to look and...

I removed the side panels as I used fans on my 2008 AE . Needed the extra room to tie wrap the harness for the fans. I read the LED headlights without the fans.will fail sooner from heat.. YMMV It's been two years 10,000 miles LED still working.

Do you have the left side paddle shifter with the on/off button?

Welcome from Ft Worth Texas