Niehart
Pie Smuggler
This is one heck of a nice jacket for $239.00. FirstGear has upgraded a few things since I bought one. Only word of warning is the coat is cut for a trim body. Other wise I would own a new one said the fat guy.
https://www.motorcyclegear.com/street/closeouts/textile_jackets_and_pants/first_gear/2010_tpg_teton_textile_motorcycle_jacket.html
•d3o™ intelligent shock absorption in the shoulders and elbows provides superior protection
•HYPERTEX™ PLUS waterproof and breathable outer shell material keeps rain outside, but allows inside humidity to escape
•Outer shell material is 100% 600 denier nylon for abrasion resistance
•Kevlar® reinforced Teramid® underlay at the crucial first point of contact on the shoulders and elbows to keep your skin safe from the road
•Minimize the heat by utilizing six vents – two 9” chest vents with cord locks to securely hold them open for airflow, two 9” sleeve cuff vents with 2-way zippers to regulate volume and two 9” rear exhaust vents
•YKK® and RiRi® waterproof zippers protect all exterior vents and pockets from moisture
•For storage there are two chest pockets plus two front side; left side contains a port for heated apparel power cord or headphones for your favorite listening device and both pockets contain pull cords to create a wind block around the bottom of the jacket; key pocket on the left sleeve. All pockets designed to deflect moisture
•Integrated in the collar is an under-the-helmet rain hood–never again will water run down your neck!
•Reflective panels on the front, side, arm and back keep you visible at night
•Adjustable waist and arm straps provide a custom fit
•3” drop-tail design keeps the jacket from riding up your back
•The main front, 2-way YKK® zipper is shielded from moisture by a double storm flap with rain gutter, held in place by spring-snap closures
•Inside the storm flap on the left side is a security pocket with a red slider for visibility–easy access to storage without having to unzip the jacket
•When not in use, hang your gloves on the d-ring located below the right front chest pocket
•If you prefer to use an active safety device, there is a loop at the center back of the jacket for an L.E.D. accessory light (sold separately)
•To block wind and retain warmth, sleeve cuffs and fleece-lined collar are tipped with neoprene
•Jacket-to-pant 10” full conjunction zipper fits easily through zipped liner portal and the mating half can be sewn onto your favorite pair of riding pants
•Stand-alone jacket included as a zip-in liner; fabric is a 3-layer laminate that is water and windproof and micro fleece lined to retain warmth
•For airflow, there are two chest vents that line up with the chest vents on the outer jacket
•A Firstgear standard; inside every jacket there is a phone pocket on the left side and a map/cargo pocket on the right side; the TPG Teton has these pockets in both the liner and the jacket and so, whether the liner is in or out, the internal pockets are in the same p
https://www.motorcyclegear.com/street/closeouts/textile_jackets_and_pants/first_gear/2010_tpg_teton_textile_motorcycle_jacket.html
•d3o™ intelligent shock absorption in the shoulders and elbows provides superior protection
•HYPERTEX™ PLUS waterproof and breathable outer shell material keeps rain outside, but allows inside humidity to escape
•Outer shell material is 100% 600 denier nylon for abrasion resistance
•Kevlar® reinforced Teramid® underlay at the crucial first point of contact on the shoulders and elbows to keep your skin safe from the road
•Minimize the heat by utilizing six vents – two 9” chest vents with cord locks to securely hold them open for airflow, two 9” sleeve cuff vents with 2-way zippers to regulate volume and two 9” rear exhaust vents
•YKK® and RiRi® waterproof zippers protect all exterior vents and pockets from moisture
•For storage there are two chest pockets plus two front side; left side contains a port for heated apparel power cord or headphones for your favorite listening device and both pockets contain pull cords to create a wind block around the bottom of the jacket; key pocket on the left sleeve. All pockets designed to deflect moisture
•Integrated in the collar is an under-the-helmet rain hood–never again will water run down your neck!
•Reflective panels on the front, side, arm and back keep you visible at night
•Adjustable waist and arm straps provide a custom fit
•3” drop-tail design keeps the jacket from riding up your back
•The main front, 2-way YKK® zipper is shielded from moisture by a double storm flap with rain gutter, held in place by spring-snap closures
•Inside the storm flap on the left side is a security pocket with a red slider for visibility–easy access to storage without having to unzip the jacket
•When not in use, hang your gloves on the d-ring located below the right front chest pocket
•If you prefer to use an active safety device, there is a loop at the center back of the jacket for an L.E.D. accessory light (sold separately)
•To block wind and retain warmth, sleeve cuffs and fleece-lined collar are tipped with neoprene
•Jacket-to-pant 10” full conjunction zipper fits easily through zipped liner portal and the mating half can be sewn onto your favorite pair of riding pants
•Stand-alone jacket included as a zip-in liner; fabric is a 3-layer laminate that is water and windproof and micro fleece lined to retain warmth
•For airflow, there are two chest vents that line up with the chest vents on the outer jacket
•A Firstgear standard; inside every jacket there is a phone pocket on the left side and a map/cargo pocket on the right side; the TPG Teton has these pockets in both the liner and the jacket and so, whether the liner is in or out, the internal pockets are in the same p
