Magnetic Oil Drain Plug After 600 Miles

03HiYoSilver · Mar 4, 2008

I thought I share the pics Before/After of the Magnetic Oil Drain plug(Replaced OEM one w/New Rear Final Drive Plug) I installed just previous to the engine cases/pistons/rings rebuild mentioned in this thread https://www.fjrforum.com/forum//index.php?showtopic=100397 :

Before

After 600 miles:

After Pic 2:

Note: The White spots on the magnet appeared after I adjusted the picture's focus for clarity.

You can see the very fine shavings attached to the sides of the magnet...at least they did not go someplace they weren't supposed to!

Fred W · Mar 4, 2008

03HiYoSilver said:
I thought I share the pics Before/After of the Magnetic Oil Drain plug(Replace w/New Rear Final Drive Plug) I installed just previous to the engine cases/pistons/rings rebuild:
Before

After 600 miles:

After Pic 2:

You can see the very fine shavings attached to the sides of the magnet...at least they did not go someplace they weren't supposed to!

Check inside the oil filter. I bet that's a lot fuzzier. But every little bit helps...

Oh, and good choice sticking with the original copper gasket.

Crush washers? Crush washers? We ain't got no Crush washers...

Afast03nNJ · Mar 4, 2008

03HiYoSilver said:
at least they did not go someplace they weren't supposed to!

Like the oil filter? :blink:

Those pics don't look normal to me. That seems excessive.

Was that the first oil change on a newly rebuilt motor?

03HiYoSilver · Mar 4, 2008

Afast03nNJ said:
03HiYoSilver said:

at least they did not go someplace they weren't supposed to!

Click to expand...

Like the oil filter? :blink:

Those pics don't look normal to me. That seems excessive.

Was that the first oil change on a newly rebuilt motor?

This was the first Oil Change after the engine cases/pistons/rings rebuild.

weekend rider · Mar 4, 2008

normal

C&C · Mar 5, 2008

Probably all right considering the engine work done. I sure wouldn't want to see that at my next oil change though. (If it were my bike, I would crack open the spent oil filter just being curious as to what else was floating around.)

vabrzn · Mar 5, 2008

I installed a magnetic drain plug on my 2007 at 200 miles. The magnet looked similiar to yours for the next two oil changes. At 19,000 miles I have a small amount on top of the magnet each oil change.

VTXEDFJR · Mar 5, 2008

Where can you get the magnetic oil plug.

Steve

v65 · Mar 5, 2008

VTXEDFJR said:
Where can you get the magnetic oil plug.
Steve

It's the same plug as the one in the differential.

03HiYoSilver · Mar 5, 2008

In case you are interested in getting the Magnetic Drain Plug it is located Under Drive Shaft in Yamaha's Microfiche:

3JL-13455-00-00 PLUG #28 Bottom One!

VTXEDFJR · Mar 5, 2008

And I take it, it fits fine. Same torque when tighting?

Steve

Rickster · Mar 5, 2008

03HiYoSilver said:
In case you are interested in getting the Magnetic Drain Plug it is located Under Drive Shaft in Yamaha's Microfiche:
3JL-13455-00-00 PLUG

I added a link in the Gen II Bin. Can someone verify this part number for Gen II FJRs?

03HiYoSilver · Mar 5, 2008

Rickster said:
03HiYoSilver said:

In case you are interested in getting the Magnetic Drain Plug it is located Under Drive Shaft in Yamaha's Microfiche:
3JL-13455-00-00 PLUG

Click to expand...

I added a link in the Gen II Bin. Can someone verify this part number for Gen II FJRs?

Rickster,

This is the Bottom drain plug off the Microfiche for the 2007

90340-14004-00 PLUG, STRAIGHT SCREW #28 Bottom One!

Hope this helps

03HiYoSilver · Mar 5, 2008

VTXEDFJR said:
And I take it, it fits fine. Same torque when tighting?
Steve

Steve, It fits fine and you install it just like the Original drain plug... this one just has a Magnet with it.

Checkswrecks · Mar 6, 2008

I've alway just put a big magnet on the bottom of the oil filter. I've cut a couple of filters open and yes it does work.

03HiYoSilver · Mar 9, 2008

Just in case you wanted to see an OEM Oil Filter opened up, here it is:

Top of Oil Filter is the End towards the Closed End of the Filter.

Note: The Metallic Specks are from the Hacksaw Cutting through the can.

You are not going to see much fine metallic shavings in the media without a great deal of additional effort and/or processes I am not willing to undertake.

vabrzn · Mar 9, 2008

03HiYoSilver said:
Just in case you wanted to see an OEM Oil Filter opened up, here it is:
Top of Oil Filter is the End towards the Closed End of the Filter.

Note: The Metallic Specks are from the Hacksaw Cutting through the can.

You are not going to see much fine metallic shavings in the media without a great deal of additional effort and/or processes I am not willing to undertake.

The photo below is from my second oil change. I had put rectangular magnets on the filter I had taken off of a Sears socket holder. I can't totally remember what the element looked like, but it was blackish. As long as what you're finding in there is primarily a black paste, I don't think you have anything to worry about. The amount you find should be signicantly less after your next oil change; the black paste, which is fine metallic particulars, will always be there in lesser amounts.

Joe2Lmaker · Mar 9, 2008

O.K. I've got a question

If you didn't stick a magnet on your oil filter, where would those particles end up?

In the paper element? So what are you gaining?

And, since there is no filtering of the final drive oil... Isn't the magnet on that drain plug more of a "something is better than nothing" solution? It's only going to hold the largest ferrous chips anyway. Right? Adding a magnet to your crank case drain plug attracts particles that would end up in your filter anyway.

Wicked Webby · Mar 9, 2008

Joe2Lmaker said:
O.K. I've got a question
If you didn't stick a magnet on your oil filter, where would those particles end up?

In the paper element? So what are you gaining?

And, since there is no filtering of the final drive oil... Isn't the magnet on that drain plug more of a "something is better than nothing" solution? It's only going to hold the largest ferrous chips anyway. Right? Adding a magnet to your crank case drain plug attracts particles that would end up in your filter anyway.

Neat idea BUT, I agree with Joe2lmaker's above statements.

WW

Magnetic Oil Drain Plug After 600 Miles

Help Support Yamaha FJR Motorcycle Forum:

Well-known member

1 Wheel Drive

Well-known member

Well-known member

Well-known member

Well-known member

Well-known member

Well-known member

ouch

Well-known member

Well-known member

Well-known member

Well-known member

Well-known member

Well-known member

Well-known member

Well-known member

Well-known member

Right is Harder than Wrong.

Similar threads

Join the conversation!

Join today and get all the highlights of this community direct to your inbox. It's FREE!