Plug wire/connector separation...

Yamaha FJR Motorcycle Forum

Help Support Yamaha FJR Motorcycle Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

soderstromk

Active member
FJR Supporter
Joined
Apr 11, 2023
Messages
30
Reaction score
32
Location
Greenville, NC
IMG_20240601_154305301_HDR.jpg
Finally getting around to checking valve clearances ('07 with 55K and I think I might be the first one in here). And I and did this.

The last type of vehicle I did my own work on (89 Mazda pickup) I knew how to fix this.

On this beast I'm not so sure. I don't even know where the other end of this thing starts.

What am I in for here? Any repair advice?

TIA!

Edit: To attach a picture of the wire end. It's green. Hard to tell if it's corroded copper or some other verdigris.
 

Attachments

  • IMG_20240601_173733973.jpg
    IMG_20240601_173733973.jpg
    638.8 KB
Last edited:
Corroded copper. Trim a minimal amount off the end of the wire (there isn't much spare length so maybe a 1/4" or so).
Inside the top of the plug boot, there is sort of a skinny spiral spike (I assume it didn't break off). Essentially, you screw the spike into the wire by twisting the boot.

Before reinstalling the boot/wire onto the plug, smear a THIN coating of silicone grease on the rubber that contacts the valve cover and clean the rim of the opening in the valve cover. Makes future removal easier. A thin smear at the end of the boot where the boot contacts the plug insulator helps as well. The silicone dielectric grease is also helpful for the headlight boots...
 
What RossKean said, plus take a good look inside the boot at the "skinny spiral spike" and make sure its not corroded. I recently trimmed all my wires and had to replace a boot ....and long story short, one of the boots I bought off ebay was corroded to the point of the "spiral spike" inside the boot was no longer there. Hope that's not the case for you.
 
Thanks guys! The advice here is pure gold.

It's hard to see down into the top of the boot but it looks more like a post and less like a spiral/screw. May be best to replace just to be sure. It didn't come off from pulling - although some grease would have made things easier. It came apart when pushing it under the cooling system plumbing - I bent it and it came apart.

When removing the cooling system plumbing I noted much corrosion. It was so bad that I think one of the o-rings had disintegrated. Only the right side o-ring was intact.

I read somewhere there should be three o-rings, but I've only encountered these two so far - and I don't see where a third will come from.

Maybe this will become obvious when I finally pull the valve cover?

Final question (and again TIA): I'm planning on deleting the AIC? system - all the extraneous emissions plumbing. I have a set of plates and see where they go. What I'm not sure of is what to do with the single electrical connection. Do I just unplug and remove the device on the hanger? I'll add a picture to illustrate. If I just unplug it will the sensor system detect a problem?
 

Attachments

  • IMG_20240601_174550935_HDR.jpg
    IMG_20240601_174550935_HDR.jpg
    2.6 MB
Gen I has a third o-ring that should be replaced at the thermostat. Gen II has just the two for the coolant pipe.
Used coils (with attached wires) plus plug boots are often found on eBay. Be vary careful about wire routing around the coolant pipe. Yamaha should have spent an extra nickel to give us another inch of wire!

No issues with Gen II for the AIS. Gen III+ will complain.
 
Your accidental separation of the plug cap from the wire is a golden opportunity to check the resistance of the plug cap.
Using a VOM set to the Ohms resistance scale, measure the resistance from the spiral spike end to the inside connector that plugs onto the spark plug. Should find approximately 10,000 ohms resistance, or thereabouts.
If significantly different, the cap can be disassembled by using a screwdriver inside the end that plugs onto the spark plug to unscrew the connector.
Inside the cap will be a spring and a resistor slug. Clean up all the parts, including inside the cap and reassemble.
Re-check for total resistance and if approximately 10,000 ohms, good to go.
Push / screw the cap back onto the spark plug wire.

If you find the first one out of spec., might be a good idea to check the others, too.



dan
 
Thanks, Dan! I did figure-out how to unscrew it and release the spring and (what I now know is a) resistor plug. The plug did have some oxidation that came right off.

I have it all back together now and it's working, otherwise I'd do the test you recommend. I took off about 0.25" from the wire and did my best to screw it back on and it seems to have worked.

I really appreciate the advice here!
 
Reviving a thread. This just happened to me as well. Maybe I'm a little dense, but can someone please explain exactly what to do? I understand trim back some of the insulation around the actual plug wire, but then what do you do with the exposed wire and the boot it separated from? Thank you.
 
Reviving a thread. This just happened to me as well. Maybe I'm a little dense, but can someone please explain exactly what to do? I understand trim back some of the insulation around the actual plug wire, but then what do you do with the exposed wire and the boot it separated from? Thank you.
Don't trim back much - Yamaha wasn't overly generous with their wire!! Just enough (1/4"?) to get to unoxidized copper. You can spread the wires across the insulation - there won't be much. The spiral "spike" in the sparkplug boot just screws into the end of the wire.

Note: Use a thin smear of silicone dielectric grease on the tip of the boot and on the rubber flange to facilitate future removal. of plug boots. Never pull on the wires. Unscrew rather than pull if you have to remove the boots from the wires in the future. This is for Gen I and Gen II. The Gen III+ COP is different.
 
Thank you. So I did strip back about 1/4". The strands of wire are silver colored. Do I just leave them extended straight out from the insulation, or bend the strands back over onto the insulation and then twist the boot onto the wire?
 
Thank you. So I did strip back about 1/4". The strands of wire are silver colored. Do I just leave them extended straight out from the insulation, or bend the strands back over onto the insulation and then twist the boot onto the wire?
Probably doesn't matter but I would likely bend them back...
You see the spiral spike that goes into the wire?
 
You don't need to strip any of the wire. Just cut it flush. The spike screws into the center of the wire to contact the conductor(s).
 

Latest posts

Top