Oil filter wrench for my FJR?

[Jon]

I installed William Riley's highway pegs and mounting plates on my Gen II. While they work great, and give me a place to stretch out my legs, the oil filter is covered up by the plate. I have the cup style oil filter wrench which has a 3/8" socket drive in its center. To use it to remove the oil filter I have to remove the peg mounting plate, something I don't want to do every time I change oil.

Does anyone know of a flat wrench style oil filter wrench that I could use. I had one for my Goldwing that was slim. There is enough clearance between the filter and peg plate for a flat wrench.

Any help would be appreciated.

 

[Niehart]

Jon, is there room to get the old style strap wrench on the filter?

 

[Ignacio]

I don't know why anybody would bother with a wrench. Finger tight with a finger tip of oil on the o-ring is more than adequate in every oil filter I've use on any vehicle including the FJR.

 

[Mr Bill]

Does anyone know of a flat wrench style oil filter wrench that I could use. I had one for my Goldwing that was slim. There is enough clearance between the filter and peg plate for a flat wrench.

I have a Gen1 and Old Wild Bill highway bars. My strap wrench won't fit around the brackets so I use a pipe wrench to take the old filter off.

 

[odot]

I'd just use a hammer like I would with a tb sync.

 

[madmike2]

I use a large pair of "channel-lock" pliers.

 

[Zorlac]

OK, now that the wrench question is put to bed, is it possible to actually remove the oil filter without removing the peg plate?

I changed the oil right before I added the pegs, so I haven't answered this for myself yet.

 

[SkooterG]

Yes, as has been reported a BAZILLION times, you still have enough room to remove the oil filter with the 'Wild Bill' highway peg brackets installed.

Jon - I too had used the cap style oil filter thing-a-ma-bob before the highway peg brackets were installed. Since it obviously doesnt work anymore, I went to Sears on and bought a set of 3 strap wrenches for like $15. So now I use a strap wrench to remove the filter.

For installing, like Iggy says, hand tight works great. I've done it that way more than 20 times and never a leak. Still a bitch to get off 4,000 miles later too.

 

[Zorlac]

BAZILLION +1 now

This applies only to the OEM filter, or do the longer substitutes also clear it?

 

[Ignacio]

For installing, like Iggy says, hand tight works great. I've done it that way more than 20 times and never a leak. Still a bitch to get off 4,000 miles later too.

You're then finger-tightening it a tad too much then. It's like 1/8 turn past where it spins on. I find after 4K that it's then moderately stiff to spin off with one hand. Those things only get tighter with time.

This applies only to the OEM filter, or do the longer substitutes also clear it?

That would probably then vary with each model. You want to build a matrix?

 

[Zorlac]

Sure, a matrix of 3.

The wall mart job, maybe a Pure one, and the OEM when it comes off.

The Purolator Pure One PL14610 & the WalMart SuperTech ST7317 are supposedly 3.25" long.

I don't know if this is the same as the 5JW-13440-00 https://www.tobycreek.org/oil_filters/yamaha.shtml but it's 3/16" shy of 3 inches.

 

[RenoJohn]

easiest and can likey be used on many of your vehicles. Your local wallyworld likely carries this.

of course the pipe wrench and a screwdriver through the oil filter are equally as effective.

 

[Ignacio]

Sure, a matrix of 3.

Cool. When you get them all figured out let me know and I'll put it an the FAQ.

 

[Rls]

Sure, a matrix of 3.

Cool. When you get them all figured out let me know and I'll put it an the FAQ.

The flat wrench for my 1500 Gold Wing also fits my FJR

 

[madmike2]

This applies only to the OEM filter, or do the longer substitutes also clear it?

Sure, a matrix of 3.

Cool. When you get them all figured out let me know and I'll put it an the FAQ.

Iggy, eye wint en bot me wunna them super-duper-hevvy-doody-racin-kompyutishun o-yul felters. Et's sposed tuh be thuh reel-deel fer kleenin mah orl, butt ets a mite longer 'en them stock-uns. Willit kum offa my murdersickle if'n eye gots them rider's travelly peg things? Er em eye gunna hafta loosten up them peg holder brackits? :blink: Thuh feller et the mortersicle shop din't noe, soes eye thot yewens wood. :dribble:

And it isn't even "dog-pile Friday".

 

[Jon]

Thanks for letting me know the Goldwing wrench will work on the FJR1300. That flat wrench will slip in perfectly.

 

[FJRski]

...of course the pipe wrench and a screwdriver through the oil filter are equally as effective.

+1, I use channel locks, after all, who needs a used used oil filter in good condition, hand-tighten the new filter, there's just enough room to slip it inside the mounting plate.

 

[tyronewildman]

Well, I'll be darned---My flat Goldwing filter wrench does fit my '04 FJR Yammy filter. Why didn't someone tell me that 4 years ago?

De <_<

 

[Bounce]

I have the highway pegs and the Bike Johnny carbon fiber engine armor. I use one of the nylon strap wrenches and it slips in easily. Take up the slack and use a crescent wrench on the square metal shank. No problems! Packs easily in the tool kit.