2019 es fjr 30k miles. I swapped new slippers on rear tire - no problem. Went to change the front, did it. Rode it no further than 200 yards and got a check engine lite, TCS and abs warning. What may I have messed up?
2019 tire change problem
- Thread starter ecc1124
- Start date
Help Support Yamaha FJR Motorcycle Forum:
Rogue
Well-known member
I would guess the ABS sensor but wait till someone familiar with the front wheel ABS sensor chimes in.
A little background please, did you change the tire yourself? Or did a shop change the tire?
Is this the first time you have removed / replaced the front wheel on your scooter?
Is there the possibility that the ABS sensor ring was damaged?
Did you remove the front ABS pickup from the mounting plate on the left side and forget to replace it?
If so, did the ABS pickup get snagged in the moving mechanism and get damaged?
Even if the ABS pickup is installed correctly, is the wiring snagged in the moving mechanism or the brake caliper and damaged?
I've never tried this and am not sure it is even possible, but is there a chance the wheel was installed backwards, and the ABS sensor ring is on the right side and the ABS pickup is on the left side?
Did you remove the rear ABS pickup from the mounting plate on the right side and forget to replace it?
I mean, come on, there are only so many ways that can be assembled. Should be able to spot the problem just by looking.
Edit:
One other thing, if you did NOT remove the ABS sensors from the mounting plates, do that and check for corrosion or other damage to the sensors and the hole in the mounting plate. Clean as necessary.
dan
Last edited:
roger dodger
Well-known member
My money is on the ABS sensor also, it's probably just dangling. Also did you use anything magnetic near the sensor ring?
BILI
Active member
No offense intended, but you may have put the front wheel on backwards. That is, the ABS sensor is on the wrong side.
Trust me, it happens
Tire was installed by a Cycle Gear shop technician and is going in correct direction. I was clear about no magnets near hub. When you mention "rings" are you talking about the 2 bearings? That could be the issue. I will disassemble and reverse them to opposing hub inserts.
I tried to align the notch in abs plate so it's right behind the fork. Nothing was dangling.
I tried to align the notch in abs plate so it's right behind the fork. Nothing was dangling.
How about the sensor in the rear? That ABS plate has to be aligned right also.
- Joined
- Jul 3, 2015
- Messages
- 494
- Reaction score
- 649
Did you remove the wheels yourself and then take the wheels in to have new tires put on them? Did you then reinstall the wheels yourself? It's not clear from your initial post.
I once did this at auburn's house. When reinstalling I tried like crazy to put the front ABS ring onto the rear wheel. Then he tried. Auburn finally noticed what I had done wrong. I don't know if it's possible to actually do this, but I sure tried.
I once did this at auburn's house. When reinstalling I tried like crazy to put the front ABS ring onto the rear wheel. Then he tried. Auburn finally noticed what I had done wrong. I don't know if it's possible to actually do this, but I sure tried.
Took to a Cycle Gear shop for technician to install new tire. Clearly aware of no magnets near hub. Tire rotates in correct direction.
Took what? The whole bike or just the wheels?
The tires may be rotating in the correct direction but are they mounted on the rim in the correct direction?
Post some pics up close of the ABS plates and sensors. This issue would have nothing to do with the bearings or spacers. If that was the problem your rotors would line up incorrectly and there would be bad brake drag. I just recently had a spacer out of place and my back tire would not "free wheel" on it's own.
We're not asking if the tire rotates in the correct direction either in relation to the wheel or in relation to the direction of travel of the scooter.
We're asking if perhaps the wheel got put on the scooter in the wrong direction, with the ABS sensor ring on the wrong side.
The small notch in the front ABS sensor plate indexes on the small nub on the inside of the front fork left side.
Yes, we're asking specific questions to try to help. It would help us if there were specific answers.
dan
Ok,
I think the issue was the collars were on the wrong sides of the hubs. All lights went out except the engine which I think needs obd2 resetting. Thank you everyone for your help.
I think the issue was the collars were on the wrong sides of the hubs. All lights went out except the engine which I think needs obd2 resetting. Thank you everyone for your help.
I recently did a 200 mile ride, the last 10 miles or so the CEL, Traction Control and ABS lights all came on. Pulled over and noticed the rear ABS Sensor was dangling , the securing bolt had worked it's way loose. Had a spare bolt , put the ABS Sensor back into the hub and all was good. All lights went out. Exact duplicate of your issue perhaps?
The OP wasn't specific if it was the spacers in the front or rear. Either one would create so much scraping noise from pad on rotors that I imagine would have been very noticeable.
I think the collars were reversed. I swapped them around and all is good now.
Diablo1
Well-known member
It’s a good idea to clean the metallic dirt from the ABS sensor when you change the tire. The particles can interfere with proper operation. Also do not let the sensor touch metal.
Similar threads
