Search results

cancel recall completed

Cancel the request . I have completed the recall. Cancel request, recall completed.

Where do the large terminals plug in? Which spider does the other end terminate? How is the harness routed? Thanks

If possible, can someone post the Yamaha recall install instructions of sub harness. Part number 90891-30074. Thanks

Location Metro Detroit area Clinton Twp, MI 48035 https://s582.photobucket.com/user/billike_album/media/fjr/HPIM0850-4.jpg.html?sort=3&o=0#/user/billike_album/media/fjr/HPIM0850-4.jpg.html?sort=3&o=0&_suid=136845998082603653568452513503 2008 FJR 1300 A with ABS 1) Mileage 2,010 (two...

Bill, The recall switch cost $48.93 plus tax at K&W Cycle (Dylin ordered the switch); Roseville had a switch in stock but wanted more than $60.00 plus tax for the switch. Dealer cost on the switch is $35.71. Part number for the recall kit is 90891-30058-00. The new switch is identified by a...

Hi, I had my FJR at Macomb Powersport, they did not resolve my clutch plate issue or the ignition switch recall, this was in Feburary. (do not do business with them) I went to K&W Cycle for the ignition recall, the service manager refused to order the recalled ignition switch until the FJR...

Hi, Good pricing, have you had any luck with Macombs service department? I have not. Good luck, Bill

Hi, It is possible you installed the wrong friction plate, measure the ID of the friction plates, the approx 5" rings have to fit inside the diameter of the first friction plate installed. The clutch spring (belleville) could be installed incorrectly. Look at picture 2 and 3 closely...

Hi, I soaked my clutches overnite, submerged in Yamaha recommended oil. I used a clean anti-freeze one gal container. I changed engine oil 3 times in 1200 miles, the clutch was never right until I soaked the clutches. I did not change oil after clutch soak. Pls read follow up...

Don, I measured my stator windings after the engine was warm 08 FJR. (Snap-on dvom measured .3 and .3) (Craftsman pro dvom measured .3 and .2) and no unwanted grounds. The rectifier can be tested with a diode tester if your dvom has that function. There are six diodes, three positive and...

Hi, Thanks for the help, I repaired the link. Bill

Hi, The white dot has to face out, it going to rotate with the assembly.(there is no index for this part, just centered in the friction plate) The friction lined plates have pink index marks and they need to placed between the the two triangles on the clutch basket. The steel plates did not...

Hi, As you know by now the charging system is not charging. 13.5 V -15.5 V with 14.2 V being ideal is a typical specification with the engine running. Open circuit voltage on a fully charged battery is generally between 12.6 V to 12.8 V. Open circuit voltage is read with the engine and all...

Hi, Sh_ _46 Malfunction detecting condition-Gear position calculated by MCU (motor control unit) is different from foot shift switch. Symptom-Engine speed and gear position sensor signal do not match while vehicle is driven. As quoted from an "08" Yamaha manual. Yes FJR clutches are wet but...

Hi, I posted a how-to article on Technicial Discussions "08 FJR R&R clutch plates", Feb 8, 09. (https://www.fjrforum.com/forum//index.php?showtopic=114431) I was unable to roadtest the bike until now. Before soaking the clutches, the trans clunked into 1st, 2nd, 3rd, and 4th. When...

Hi, I posted an article on sticky clutches under Technical Disscussion, Feb 8, 09 (2008 FJR clutch soaking). Ask the dealer to soak your clutches, this will probably fix most of your problems. I have not followed up my original post with my road test results, but soaking the clutches fixed...

Hi, There have been a number of FJRs assembled with dry clutch plates causing clutch engagement and disengagement problems. (check the posts) Mine would not disengage the clutch at idle and sometimes while changing 2, 3, and 4th gear. A friend has an 07 and it was perfect from day one. Bill

2008 FJR CLUTCH PLAT SOAK PROCEDURE Before disassembly run engine until crankcase/clutch cover is warm to the touch. DISASSEMBLY 1. Remove right fairing and side cover. (optional) 2. Remove crankcase/clutch cover, 10 allen head bolts. ( pic 1) 3. Before removing 6 hex bolts, observe pink index...

Hello, I had my 08 fjr in for service, dry clutch plate issues. Jan 23, I asked about the ignition switch recall after reading Yamaha recall letter. I talked to Brad Franklin (Yamaha gov relations manager). Brad told me to contact dealer service manager and have him contact MI zone rep about...