Search results

should arrive late thursday will leave monday morning for long round about home. goal is 3800 miles to make the trip total 5000. gotta have a goal. i want a new seat and i will be close to california.

i made mine out of 1/4 aluminum plate. it's adjustable forward and back and easy to make. if you need plans or other assistance pm me.

I'm in. will be in late Thursday early Friday leaving Mon am. looking for someone to share a room with. I'm a middle aged non smoker/drinker ex sailor. i know it doesn't go together but it's true. i will be going down Thur Ohio and st Louis. but the return trip could be a little strange...

I'm in. will be in late Thursday early Friday leaving Mon am. looking for someone to share a room with. I'm a middle aged non smoker/drinker ex sailor. i know it doesn't go together but it's true. i will be going down Thur Ohio and st Louis. but the return trip could be a little strange...

go to radio shack and get two male and two female 1/8 stereo phone jacks. if you wire your mic to one female jack and your ears to the other female jack. epoxy the female jacks between the liner and shell with the hole pointing down and just visible at the bottom edge of your helmet. i like it...

my first question is is the bolt stainless if it is the locktite wont work without locktite primer. locktite needs contact with carbon to set. some types of stainless bolts in aluminum will not cause the chemical process that locks the bolt. the other thing to look at is what others have said...

Shawn, hope to see you there. I'll just look for the aye hole. :yahoo: it will be a good ride for me. maybe i can drag one of my sons along.

as stated many times hair spray is good as long as you don't ride in the rain. it is water soluble and if you ride in a long rain storm the grips will start to squirm around and slip. i have experienced this personally and its not much fun.

fjrshanta those tig welds are beautiful. its nice to see someone who doesn't feel the need to weld everything at 90 amps. thats the object of tig keep the heat as low as possible to achieve required penetration. again very nice work. your either a confidant, competent fabricator or a novice. i'm...

thats already in the works. picture an anodized upper clamp with rubber bar mounts for taper bars and this clamping system. the proof of concept for testing clamping strength is almost done. if it proves strong enough then it will be time to make the real upper clamp. i have a lot of metal...

dcarver and haulin. i prefer to gently persuade things rather than drive them so this is what i have in mind after seeing your photos and reading what you have written. . i assume the sleeve that was made by gps is solid not two piece like some fork seal drivers that you see for driving seals...

dcarver, yes i'm still interested in helping out you and the forum anyway i can. my big lathe can spin 16" X 52" so i dont see a problem. e-mail me what you want and exact specs or give me a call and we can talk about it. my e-mail is [email protected]

dcarver, i have a few machine tools and a little time so if you would like i could make you a tool simular to the motion pro but with a longer snout. it would clamp around the fork and you would have to provide a pipe to drive it down with. if it works you would have to do a write up and become...

the only thing i don't see mentioned is temperature. tires like to be warm and rain wont let the rubber stay warm. and the colder it is the slicker it gets. i remember an article from Motorcyclist mag from the seventies where a tire manufacturer said that the biggest loss in traction wasn't the...

as everyone else said "good job on the choice of wives". my wife got me an 08 for our 26th anniversary. she is German so it's not just the Canadian women. at least you have a few months to read up and order the must have farkles. i had an 02 connie before the fjr and there is no comparison in my...

while i like your design i don't believe you understand the function of the bolt hole you are trying to use. on one side (i think its throttle side can't remember) that bolt holds a boss to the side of the engine which the frame clamps onto. this boss will stick out varying distances due to...

best thing was the grandkids over to open presents two days in a row. since being disabled i do a lot of cooking and have asked for and finally received a good set of kyocera ceramic knives. also got the chemicals so i could start doing type 2 anodizing. which i want to do to my new upper...

the diagram shows a simple coil so there would be no polarity issues. put the wires where you want.

1) Do you even WANT the directory available as a POI? Yes 2) Do you want to be included on it? Yes 3) Would you rather have your full address published, or, just a your contact phone number? (Location would be the Centroid for your town - main post office or city hall). Theirs still risks...

when your done searching clean the area beside the bike or move the bike to a clean wall or in front of the garage door. turn on every light possible and then with a helper watching blow compressed air thru the motor toward the wall. start out from a distance and move closer and closer until you...