Search results

In all honesty, it really wasn't all me. I can read aircraft wiring prints, but I could not read those prints in the manual. A wire goes to a plug and you can't see how it continues. You have to go to Sheet 2, then, maybe you can find it, maybe you can't. I took the prints to work to have one...

Found it! After much head scratching and "Attempting" to read the schematics I finally trace the problem to the combination fuel pump and engine cut off relay. I had no idea where this was, book was no help locating it, and ended up pulling all the plastic including the front cowl. Finally...

Took the bike out for the first time today. Should have stayed home. Leaving the driveway when I shifted to 2nd the engine died. WT? Stupid sidestand I thought. Cycles the side stand a few times bike started and ran fine. Nervous at this point I rode up and down the road with in pushing distance...

I think Sunday we will probably do the Park for half a day and then go back to Har Barbor so the "Shopping Queen" can poke around town for a few hours. This leaves me to people watch on the Main St. I'm good with that. Hope it's about 90 degrees. :>)

FJRski Regarding the K&N air filters, this is my obvservation. I know alot of people use them but..... I have a Ford Diesel and on those forums there are many cases of people using the K&N filters and ruining the engines due to "Dusting" which means they ingested fine dirt. Granted these...

I'll play: Ghey Bike with 50K on the speed-o Ghey Polished Wheels Ghey Polished Exhaust Ghey Polished Suspension Thingamajig Ghey Big Butt Seat That's all. :)

It is a flat blade. On the small side, maybe 3/16 inch wide, but it needs to be about a foot long. The one I use is 18 inches but it doesn't need to be that long. It needs to fit in the hole the 10MM headed screw comes out of.

I feel your pain. I just went through the same ordeal. Datel was reading very low as I had it wired into some circuit on the bike, don't rmember what. But my DVM read higher when attached right to the Datel screws. So I ordered a new Datel thinking it was off. The new one was no better and I...

Booked and confirmed. Everything the same as you Chris. :)

Current Considerations If your staying Thursday night in Kittery Staying at Coachman Inn Dinner at Bob's Clam Hut Friday Depart Kittery Trading Post by 9 AM. Friday's ending destination is Casco Bay Inn With Dinner at Harraseeket Saturday Breakfast at Mae's Cafe and Bakery And on to...

Yeah you're right. Bout a mile up the road. That's good. There sure are alot of places to eat in town. Do we have a recomended seafood place in Bar Harbor? That Bar Harbor motel is highly rated on Trip Advisor. Excellent choice.

Wow! This all scares me because I paid for my $77 subscription (because I was going to cancel) with my credit card so they now have the number. I called the credit card people and asked to put a block on XM. "We can't do that. " Hmmmm. OK, then cancel the card and give me a new one. "That we...

I'm leaning toward the Coachman right now. We'll be in there by noon or early afternoon. Then Hope can go poke around the outlets right across the street and I don't have to go with her. Also it looks like the recomended " Bob's Clam Hut" is in the mall area so we may be able to walk to it and...

Not sure if this helps much but I was looking for a place for Hope and I to stay in Kittery on Thursday night. This place had good reviews @ $90 or $85 with AAA. Right across the street from the mall. Coachman Inn This place had almost as good, reviews for $5 less, 1/2 mile down the street...

That is perfect for my situation, which is....well I don't really have a stiuation, but I like that plan.

That's cool, but what site are you refering to? Give us the link so we can check it out too. :blink:

Agent, By now you have now been advised to check most everything from the main stand forward. All good ideas really. But we want to know what you have found. I know we have a winner here somewhere. :yahoo:

52K on an "06" bought new in May 06.

Usually when this happens it is the brake pads. The pins that go through the brake pads are a little smaller than the holes in the pads they go through. So when you rock it back and forth you can hear the pads moving slightly on the pins. You can test this by putting your finger on one of the...

I like ending in Bah Hah Bah.