Not wanting to be considered a doofus among this august society, I'm taking advantage of Audiowise's most generous offer to help sort out my torque loss. Will be riding over early tomorrow to open this thing up and find what we all seem to agree is miss-timed cams. Will document, as well as possible, in hopes of convincing the fine folks in Prosser that they not only let it slip, but can't/won't recognize their error.
Torque loss after service.
- Thread starter fjrwalker
- Start date
Help Support Yamaha FJR Motorcycle Forum:
David Morrow
Well-known member
Better leave early; I don't think I'd be wanting to do that sort of work on a hot bike.
Will be looking forward to hearing how you make out. Best of luck.
Will be looking forward to hearing how you make out. Best of luck.
escapefjrtist
Searching for Dry Roads
Good luck to you two tomorrow Jim. I'd love to join in with the teardown tomorrow, but I have commitments morning and afternoon. Rotten [no pun intended] timing!
Hope the issue is as simple as mis-timed cams.
--G
Hope the issue is as simple as mis-timed cams.
--G
TownsendsFJR1300
Well-known member
Yep, good luck.
Also, if it is off and documented, put a HOLD on your credit Card payment till the shop works something out with you
Also, if it is off and documented, put a HOLD on your credit Card payment till the shop works something out with you
Well, much as expected, both cams ******** one tooth. Also one exhaust valve with too little clearance. All is well now. Ride home was excellent. Took a video shot panning from the crank marker up to the cam markers. Hopefully that will be enough to convince the dealer that they had it wrong.
Can't thank Paul enough for his help. i'm sure I could have done it successfully, on my own, but it would have taken much longer and would have, no doubt, required much swearing.
Can't thank Paul enough for his help. i'm sure I could have done it successfully, on my own, but it would have taken much longer and would have, no doubt, required much swearing.
HotRodZilla
GOD BLESS AMERICA
On Tuesday you need to demand a refund for the ****** work they did. If they refuse, you need to contest the charge with your CC card company. NEVER go there again.
AND, very glad you got it running right.
AND, very glad you got it running right.
MCRIDER007
Well-known member
This is the same dealership that identified, documented, and supported the FJR community to help resolve and fix the "tickers". Everyone makes a mistake now and then, let's wait and see if they admit their mistake and are willing to make good on that mistake.
Niehart
Pie Smuggler
Well said. Waiting until we see the shops handling of this.
escapefjrtist
Searching for Dry Roads
Good for you Jim. Glad it was an easy find & fix and you were able to correct a tight valve too.
--G
--G
Niehart
Pie Smuggler
And, yes, Paul is good hand.
HotRodZilla
GOD BLESS AMERICA
Then they shouldn't have any problem admitting their screw up and making it right with the customer. I'm pretty sure I said the same thing Steve said. If they admit their mistake, and refund his money, they'll have made it right. What else do you guys expect? Keep his money but apologize profusely?
I'm glad your ride home was uneventful and that the bike is now running properly.
Here is a photo of the cam timing at TDC on the Crank. You can see the yellow dot on the intake cam and the arrow on the exhaust cam; they are visibly quite off. Finding the exhaust valve that was a tight 0.006" (the bike was nice and cool at that point) was also a bit of a surprise.
The dealership gets an extra ding for taking a second look at the bike (and charging for it) and not finding this. I rode the bike, after 5000 RPM, there was no useful power.
Here is a photo of the cam timing at TDC on the Crank. You can see the yellow dot on the intake cam and the arrow on the exhaust cam; they are visibly quite off. Finding the exhaust valve that was a tight 0.006" (the bike was nice and cool at that point) was also a bit of a surprise.
The dealership gets an extra ding for taking a second look at the bike (and charging for it) and not finding this. I rode the bike, after 5000 RPM, there was no useful power.
TownsendsFJR1300
Well-known member
Also, per your first post, NO VALVE ADJUSTMENT WAS NECESSARY... WTH??
Agreed, give them a chance to make it right or CONTEST THE CREDIT CARD CHARGE.
They apparently didn't check them, or at the very least, didn't find and adjust the one.
Question, did it appear ANYONE actually got to the valve cover and R&R'ed it? It should show
hand prints, dirt moved, cleaned, etc.?
Agreed, give them a chance to make it right or CONTEST THE CREDIT CARD CHARGE.
They apparently didn't check them, or at the very least, didn't find and adjust the one.
Question, did it appear ANYONE actually got to the valve cover and R&R'ed it? It should show
hand prints, dirt moved, cleaned, etc.?
RaYzerman19
Go Wings!
I would give the dealer a chance to respond........ especially the tight valve clearance, but, it's not that hard to see where the timing went off.
IF the tech did not remove the right engine cover, he could not see the timing marks. Nor would he have zip tied the cam chain as WE all know how to do (it's not in the manual) during a CCT change. Unfortunately that inspection plug is there to tempt you to be lazy....... has been removed for GenIII.
Kudos to Paul and yourself for getting it all straight........ gotta love those PNW guys!
IF the tech did not remove the right engine cover, he could not see the timing marks. Nor would he have zip tied the cam chain as WE all know how to do (it's not in the manual) during a CCT change. Unfortunately that inspection plug is there to tempt you to be lazy....... has been removed for GenIII.
Kudos to Paul and yourself for getting it all straight........ gotta love those PNW guys!
Last edited by a moderator:
MCRIDER007
Well-known member
Ah.....don't know if Ray can see it.....but now I can see it....and I sure couldn't without the circles. It would have helped if I had known what I was looking for.
Last edited by a moderator:
RaYzerman19
Go Wings!
Ha ha, I might be old, but I figured it out on the first pics... BTDT. Another way to look at it is rotate the cams until the marks do line up, then look at the crankshaft end. It will be off, and what's most likely happened is the chain dropped down while the CCT was out.......... if the tech didn't take the right side cover off, and zip tie, that's the risk one takes.... and without the cover off, he wouldn't have known the crank position relative to the cams.
Last edited by a moderator:
wheatonFJR
...
That was then...if they are a good shop still, they will do right. Otherwise I'm with AJ. Well done in 2005 does not forgive this in 2016.
escapefjrtist
Searching for Dry Roads
I had my glasses and still didn't see the marks. Thanks for circling the arrows Paul!
--G
--G
Well, I'm am waiting, less and less patiently, to hear back from Dan Denchel, owner of DVPS.
I spoke with him Tuesday morning when I called for Mike the service manager, who was out.
Interestingly Dan was already aware that there was an issue as a friend of his had directed him to this thread.
He seemed accepting of the idea of some adjustment but wanted to gather more info.
We shall see....
I spoke with him Tuesday morning when I called for Mike the service manager, who was out.
Interestingly Dan was already aware that there was an issue as a friend of his had directed him to this thread.
He seemed accepting of the idea of some adjustment but wanted to gather more info.
We shall see....
Similar threads
