Joe2Lmaker
Well-known member
I taped the template for the Rev2 support to the Rev1 support and test fit that:
I'm sure it will work. Unfortunately Shane took his GenI and Givi rack to Iowa.
Last edited by a moderator:
Auxiliary Cell Design
- Thread starter Joe2Lmaker
- Start date
Help Support Yamaha FJR Motorcycle Forum:
I'm sure it will work. Unfortunately Shane took his GenI and Givi rack to Iowa.
Joe2Lmaker
Well-known member
I'm working on it.
This morning I was looking into packaging. This tank is a little wider than the Tag-Along Tank. I had to make sure I could stay under the UPS Dimensional Weight penalty. Now that I have that figured out, I'll update the CAD model. The welder made a couple of suggestions and I'll make a couple of slight changes that will help him out. I doubt most people would be able to spot the difference. I hope to have that done by the end of the week so I can submit a request for quote.
I also have an idea that might make the GenI supports less expensive to produce. I'll still complete the three sets that I have started.
There are two gentlemen who have dibs on the first two tank prototypes (and supports). If they pass, I'll need to find someone to buy those before I offer a Group Buy.
I also want to check the fit on an ST1300. If we can generate some interest there, it will also bring the price down.
In the end, the price is going to be determined by the amount of interest. Because of the bends and radii, these are much cheaper if we can produce several at a time.
Joe2Lmaker
Well-known member
I understand that you GenI owners love your bikes, but Damn! The geometry of that rear subframe is a challenge.
I wanted more of the bottom plate of the tank supported. But the tail cover was crowding in.
I'm going to try swapping the right and left supports and leaving a little more material. Something like this:
• •
I wanted more of the bottom plate of the tank supported. But the tail cover was crowding in.
I'm going to try swapping the right and left supports and leaving a little more material. Something like this:
Joe2Lmaker
Well-known member
I've tried to simplify the GenI rear seat replacing rack. Even though I was using relatively inexpensive aluminum channel, the number of set-ups was was excessive.
Why am I updating this thread on New Year's Eve? It might be because I am putting off watching Bridesmaids with my wife. (God help me!) It might be because I am in a particularly good mood because I just successfully barbequed salmon and enjoyed a tasty New Year's Eve dinner.
Pardon the presentation. I don't own a platter that could have done justice to that beautiful fillet.
I abandoned using this:
Even though I had a few sets of supports started:
• •
In favor of this:
I also got rid of the counterbores and decided to move the screw holes away from the vertical wall and off the corner radius:
I also added a slight angle to back edge of the support:
I bought the material and updated the models; I'll try to cut a set of supports this weekend.
Why am I updating this thread on New Year's Eve? It might be because I am putting off watching Bridesmaids with my wife. (God help me!) It might be because I am in a particularly good mood because I just successfully barbequed salmon and enjoyed a tasty New Year's Eve dinner.
Pardon the presentation. I don't own a platter that could have done justice to that beautiful fillet.
I abandoned using this:
In favor of this:
I also got rid of the counterbores and decided to move the screw holes away from the vertical wall and off the corner radius:
I also added a slight angle to back edge of the support:
I bought the material and updated the models; I'll try to cut a set of supports this weekend.
Last edited by a moderator:
Duster19
Well-known member
Joe,
Nice looking piece of fish.
Oh yeah, continue to look forward to the finished product.
Dave
Nice looking piece of fish.
Oh yeah, continue to look forward to the finished product.Dave
Joe2Lmaker
Well-known member
I had forgotten that I posted a photo of our New Year's Eve Dinner. I thought the fish you were referring to was the tank support.Nice looking piece of fish.
See the resemblance?
Those are the Revision 3 GenI tank supports.
They do the job, but they are purely utilitarian. I liked the Rev 2 supports better. But, these transfer weight to a larger footprint on the rear subframe.
I found some anchor nuts with longer springs and I really like them:
Once installed, they really stay put!
The left side of the bike has these zip ties and installing the anchor nuts is a pain. I would really like to just cut those damn things, but I'm not a GenI owner and I haven't taken the time to figure out why they are necessary.
This shows the clearance with the seat pan:
It isn't very clear in this shot, but the top edge of a Russell seat is snug up against the tank. There is room in front of the OEM rack to adjust the supports, moving the tank back a little so the seat doesn't rub.
Feedback? Criticism?
"Is this mike on? I know you're out there. I can hear you breathing."- Henny Youngman
Last edited by a moderator:
I really like the way it looks. I don't suppose you know if it will clear an OEM trunk? It's hard to tell for sure in the pics. It looks like the tank is around 5-6" taller than the grab rail/rack? Will it come in anodized blue? :thumbsup:
Nice work!
PhilJet09
Nondescript FJR Hierarchy Displayed
I'm liking it, just waiting to see a finished GenII/low seat shot and pricing.
Joe2Lmaker
Well-known member
Good question.
I’m trying to remember if I know any Minnesotans with a GenI and an OEM trunk. January 20 the tank and rack are making a trip to Iowa to see how they fit with a GIVI rack and trunk.
I wish I still had the poly cell. The idea was to make a rack that would work with this aluminum tank and the inexpensive inverted poly tank. But, I sold the poly tank <_<
Inexpensive, inexpensive, inexpensive.
That's been my mantra lately, but it's tough. I'm too much of a perfectionist. For example, the gap behind the tank is bugging the hell out of me. Does anyone else look at that and think "WTF? You could pull a rabbit outta that!"?
This is what I can tell you. The hinges on the OEM trunk start to protrude forward of the grab rail/rack at a height of 6" above the grab rail. At 5" above the grab rail the body of the trunk is still rear ward of the front edge of the grab rail. ...If that all makes sense...
That gap behind the tank looks fine/normal to me.
Joe2Lmaker
Well-known member
:dribble:
I'm guessing, but the height from the top of the OEM rack to the top of the tank must be like 3 inches.
Someone should PM Bustanut to verify that dimension for us.
J/K I'm sure Dolly loves the Angry Inch
The height (and angle) of your filler neck will have more to do with clearing your trunk than the tank itself. (again ... guessing)
Thank you for that.
But, after talking to Duster19 we decided I'm going to make a Rev 4. set of supports.
Last edited by a moderator:
Bustanut joker
Well-known member
Damn Joe! Yer givin' me an extra inch of credibility there..
I'm starting to like you :lol:
I'm starting to like you :lol:
txvoyager
Well-known member
Does this help? Sure looks like it would fit (although I just noticed I measured from a slightly different plane on the rack)...
Joe2Lmaker
Well-known member
Rev 4 GenI supports:
So far we've checked the fit with an OEM seat and with a Russell. The OEM just touches the tank and the Russell has about 3/16" gap.
So far we've checked the fit with an OEM seat and with a Russell. The OEM just touches the tank and the Russell has about 3/16" gap.
dcarver
Well-known member
That looks incredibly sexy..
Shane
Well-known member
Seems strangely familiar...
Last edited by a moderator:
